Sink Installation in Denver, CO
A new sink has to fit the counter cutout, sit level, and drain properly from the first run of water. We measure first, check the drain and supplies, and set the basin so it stays put.
Service overview
Fit, drain, and supplies before the basin goes in
Sink installation in Denver means fitting a new kitchen or bathroom sink where an old one has failed or where a room is being remodelled, and the work starts with measurements. The counter cutout, the basin dimensions, and the drain position decide which sinks will fit, and a sink bought without measuring often does not sit in the counter at all. The drain and the supplies underneath matter just as much: older homes often have original traps and shutoffs that have seized, or supply lines that are brittle and due for replacement at the same time. We check the counter, the drain, and the supplies before the new basin goes in.
! Problems we solve
Will it fit this counter
Cutout size, basin dimensions, and drain position decide which sinks work. We measure before the sink is chosen, not after it is bought.
Kitchen or bathroom
A kitchen sink and a bathroom basin are different fixtures with different mounts, drains, and faucet needs, and each is fitted differently.
What is underneath
Under an old basin, the trap, the shutoffs and the supply lines have usually aged together: seized brass, brittle lines and a trap past its best. All three need attention before a new sink can be connected.
Scope of work
What a sink installation includes
A sink installation runs in a set order: measure the cutout, check the drain and the supplies, set the basin, then seal and test it. Here is what it covers.
-
01
Measuring and selection
We measure the counter cutout and the drain position, and confirm the sink you have chosen fits the counter before any work starts.
-
02
Removal and drain check
The old sink is removed and hauled away. The drain and trap are checked, and the shutoffs and supply lines are inspected.
-
03
Setting and connecting
The new basin is set level and sealed to the counter, the drain and trap are connected, and the faucet is fitted and connected to the supplies.
-
04
Testing and adjustment
We run the sink, check every connection for leaks, and confirm the drain runs clear and the faucet shuts off cleanly.
What we check underneath before we start
Under the sink of an older Denver home, the trap may be original brass or cast iron, the shutoffs may be seized, and the supply lines may be brittle. We check those before the install so a seized valve does not turn a sink swap into a bigger job.
Call (720) 599-7253Tools and methods we use
Measuring and level tools
Confirms the cutout dimensions and that the basin sits level, so it fits the counter and drains properly.
Basin wrench
A basin wrench reaches the faucet and trap nuts under the sink, so the basin assembly is set without disturbing the counter.
Drain and trap tools
Fits the drain and trap at the right height so the sink empties properly and the trap holds its seal.
Leak testing
Runs the sink and checks every connection so no joint is left untested.
Local execution
The city's kitchen and bathroom mix decides how a sink install goes. Remodelled kitchens in Cherry Creek and Washington Park often have stone counters with specific cutouts, so the basin has to match the counter, not the other way around. Older bungalows in Highland and Berkeley still have original sink bases, and the cutout on a 1920s base does not always match a modern basin — so we measure before anything is ordered. Denver Water reports hardness of about 89–105 mg/L (5.2–6.1 gpg), which is why we also talk about finishes that stand up to mineral deposits.
What Denver counters ask of a new sink
What to tell us when you call
New sink to fit? Call to discuss it
What to do while you plan
Measure the cutout before ordering the sink: a basin that does not fit the counter is a return trip, not an install. Call (720) 599-7253, describe the sink and the counter, and we will confirm availability when you call. If the old sink is leaking into the cabinet, shut off the angle stops under the sink and place a bucket beneath the trap.
What to expect from your sink installation
Call and describe the job
Call (720) 599-7253 once the sink is chosen. Tell us about the counter, the cutout and the drain, and whether the shutoffs underneath work — that is what sets the time for the visit.
Measuring and drain check
We measure the cutout and drain position, confirm the sink fits, and check the trap, supplies, and shutoffs under the sink before any work starts.
Setting and testing
The old sink is removed, the new basin is set and sealed, the drain and faucet are connected, and every joint is tested so the sink drains clear and the cabinet stays dry.
What shapes the cost of sink installation in Denver
The price of a sink installation depends on the sink, the counter and the state of the drain and supplies underneath, so no price is published on this site. Before any work starts, we talk through what the install involves so you can decide with the facts in front of you.
Sink and mount type
An undermount sink and a drop-in sink are different installs, and a kitchen sink with a disposal is different again. The fixture sets much of the scope.
Counter and cutout
Each counter brings its own fitting questions — stone, thick decks, older bases with non-standard cutouts — and the counter, not the basin, decides the work.
Drain and supply condition
A sound trap and working shutoffs keep the job simple. A corroded trap and seized valves add work that has to be done before the sink can be connected.
Before any work starts
Frequently asked questions
Will any sink fit my counter?
Not necessarily. Cutout size, basin dimensions, and drain position decide which sinks work, and a sink bought without measuring often does not fit. We measure before the sink is chosen, not after it is bought.
Do my shutoff valves need replacing with the sink?
Often, yes, in older homes. A sink swap means disconnecting the trap, the drain and the supplies, and original brass shutoffs and brittle lines under an old basin can fail once they are disturbed. We check them before the install and replace them when they are not sound.
Can you install a sink I bought myself?
Yes — bring the sink and its mounting hardware. The cutout is measured and the drain checked first, and a sink that does not fit is flagged before any work starts, not after the old one is out.
Does a new sink need a permit in Denver?
Swapping a sink for one that fits the same cutout is generally exempt from a permit under the Denver Building Code. Moving the drain or reworking the layout can trigger one, and we will tell you if the job you have in mind crosses that line.
Further reading: How to unclog a kitchen sink drain without chemicals.
Related services
New sink for your Denver home? Call us
Call (720) 599-7253 about the sink and the counter, and we will check the fit before quoting anything.